FSP250C-1A KIT

Tankless Water Heater Descaling Flush Kit

$89.99 USDIn stock

Service kits & accessories / FSP250C-1A KIT

1 / 6 · The kit

Check your fit: 3/4 in GHT heater service ports required. Cleaning solution is not included.

Free standard shipping to eligible U.S. addresses.

Usually ships in 1–2 business days.

Estimated delivery: 3–5 business days after dispatch.

Shipping policy

TANKLESS WATER HEATER MAINTENANCE

FSP250C-1A KITTankless water heater
flush kit.

Pump, bucket and service hoses together. Build a flushing loop around your heater’s maintenance instructions.

$89.99 USD

In stock

Free standard shipping to eligible U.S. addresses.
Usually ships in 1–2 business days.
Estimated delivery: 3–5 business days after dispatch. Shipping policy.

PUMP
1/4 HP
BUCKET
4 gal
HOSES
2 × 6 ft
  • Two 6 ft, color-striped service hoses
  • Bucket, lid, opener and pump adapters
  • Manual operation — stay with the job
Cleaning solution is not included.

Confirm 3/4 in GHT service connections. Use only a heater-approved solution that is compatible with the pump and hoses.

You MUST use a properly grounded GFCI outlet.Keep plugs and electrical connections dry.

Illustrative FSP250C-1A KIT maintenance scene: pump inside the original white bucket, blue supply hose to cold service port, red return hose to the same bucket, separate black power cable. Not a universal installation or test photograph.

FLUENTPOWER / FSP250C-1A KIT

Make tankless
maintenance clearer.

Pump, bucket and hoses.
One understandable setup.

Illustrative maintenance setup · Follow your heater’s procedure · Cleaning solution and service valves not included

FSP250C-1A KIT / PRODUCT VIDEOS

Watch it work.

See the setup. See it in use.

SETUP & USE

Flush and descale your heater

UNDERSTAND THE LOOP

See where
the solution goes.

The real kit, shown through a transparent bucket so the pump and both hose routes stay visible.

Transparent-bucket illustration. The supplied bucket is opaque white.
Illustrative routing, not a heater-specific valve procedure.
01 / SUPPLY

Pump to cold port.

Blue-striped hose carries solution from the pump outlet to the cold-water service connection.

02 / RETURN

Hot port to bucket.

Red-striped hose returns solution to the same bucket, separate from the pump outlet.

Water-side service ports only.
Never connect a hose to gas hardware.

ASSEMBLING

Two connections.
A clearer close-up.

Disconnect power before assembly. Match the supplied 3/4 in GHT hose ends to compatible water-side service ports.

  1. 01At the pump.

    Fit the threaded adapter, then seat the blue-striped hose swivel and its washer.

  2. 02At the heater.

    Blue to cold; red to hot. Follow your heater’s isolation and service procedure.

Reference-based assembly illustrations · Heater and service valves not included · Do not force mismatched threads

Fitting & safe-use notes

GHT is not NPT. Gasket-sealed hose swivels use their washer; do not add tape to the sealing face. Fit the supplied threaded adapter to the pump outlet. The black barb adapter is an alternative fitting, not an extra stage in this loop.

This overview does not replace the heater, pump or solution instructions. Isolate energy and water connections, cool and release pressure as your heater manufacturer requires. Follow the approved solution’s handling, temperature, circulation, rinse and disposal directions. Pump liquid temperature must not exceed 95°F. If unfamiliar with the procedure, use qualified service.

Keep electrical connections dry, use a properly grounded GFCI outlet and supervise operation. Keep the intake covered; never run dry or rely on automatic shutoff. Disconnect power before handling, complete the heater’s rinse/restoration procedure and never lift the pump by its cable.

STORE IT TOGETHER

One bucket.
Ready for next time.

Drain and dry after use, then tuck the pump, hoses, adapters and lid opener inside.

Everything in its place.Illustrative packing arrangement · Lid shown open to reveal contents · Store dry
Technical specifications & performanceKit contents and separate pump reference values

Pump data. Not flushing speed.

FSP250C-1A pump reference flow at discharge headFive own-model reference values: 0 ft 1900 GPH, 5 ft 1780 GPH, 10 ft 1500 GPH, 15 ft 1150 GPH, 20 ft 600 GPH. Lines are reading guides only. These are not heater-loop flow measurements.Pump flow (GPH)05001,0001,5002,0000510152025Discharge head (ft)

Five pump reference points · ft / GPH

Reading guides, not extra measured values. Maximum ratings are separate limits.

The heater, valves and service hoses change the actual operating flow.

Know the setup.

Model
FSP250C-1A KIT
Pump
FSP250C-1A · 1/4 HP
Bucket
4 gal · lid included
Service hoses
2 × 6 ft · stainless braid
Hose thread
3/4 in GHT
Control
Manual · supervised
Maximum pump flow
1,900 GPH
Maximum pump head
23 ft
Pump supply
120 V / 60 Hz
Maximum liquid temperature¹
95°F
Pump power cord¹
16.4 ft
Cleaning solution
Not included

¹ Pump manual reference for liquid temperature and power-cord length. Maximum flow and head are separate limits, not guaranteed heater-loop operating points.

Before you connect.

Is cleaning solution included?

No. Choose only a solution permitted for your specific water heater and compatible with the pump and hoses. Follow its quantity, temperature, handling and disposal instructions.

Will the supplied hoses fit every heater?

No universal fit is assumed. The supplied hoses use 3/4 in GHT connections. Confirm that your installed service or isolation valves accept the supplied hose ends; valves are not included.

How long should I circulate the solution?

Use the procedure for your exact heater and cleaning solution. There is no universal 30-minute cleaning time, and circulation time is not determined by the pump’s maximum flow rating.

Does the pump switch off automatically?

This is a manually controlled pump, not an automatic pressure-sensing system. Supervise operation and disconnect power before the liquid level falls too low. Never run dry.

Can I use the printed performance values as flushing flow?

No. They are pump reference values at stated head heights, not measured flow through a heater. Service valves, the heater water path, hose length and fittings change the operating point.

COMPARE THE TWO KITS

Choose the setup.
Not just the horsepower.

FSP250C-1A KIT: 1/4 HP pump and 4-gallon bucket. FSP400C-2 KIT: 1/2 HP pump and 5.3-gallon bucket. Both include two 6-foot stainless-steel hoses and a bucket lid opener.

Check bucket space, hose routing and your heater’s service connections. More horsepower does not guarantee a faster flush; follow the heater’s specified solution and procedure.

Read the flushing-kit comparison and setup guide →

MODEL-FIRST SUPPORT

Check the fit.
Then build the loop.

Ask about FSP250C-1A KIT and your heater’s service connections.

1 / 6 · The kit